Review: Abracon ABPSM-ULN-A – Precision Power Supply Module

When bench testing noise sensitive circuits, one needs an ultra clean power source. Low noise lab power supplies are usually bulky and expensive. Abracon challenges both the bulkiness and the expensiveness with their new low noise pocket sized ABPSM-ULN-A ultra low noise power supply module.

With the ABPSM-ULN-A, Abracon intends to set a new standard regarding price and size for ultra low noise power supplies [1]. Abracon shipped out a review sample of their ABPSM-ULN-A modules to me and today’s rainy weather is perfect for a quick review.

My boxed up review sample of Abracon's ABPSM-ULN-A

My boxed up review sample of Abracon’s ABPSM-ULN -A

The ABPSM-ULN-A ultra low noise power supply module comes with a switch mode power supply. Thanks to the wide mains supply voltage range of 100 – 240 Volts at 50 / 60 Hz and a bunch of different outlet connectors, the module can easily be used worldwide. I’d like to note that the switch mode power supply is a regular off-the-shelf supply, therefore it can be assumed that any other ‘dirty’ 6 V source would do the trick without compromising the excellent noise density of the ABPSM-ULN-A.

Unboxing of the ABPSM-ULN -A

Unboxing of the ABPSM-ULN-A

There are 4 fixed voltage channels on the device with the industry standard voltages 1.8 V, 2.5 V, 3.3 V, and 5 V. Each channel supplies up to 200 mA. The output impedance is rated at max. 0.20 Ohms. The 4 low noise supply voltages are available from one SMA connector per channel. I like the SMA connectors as opposed to ‘regular’ banana plug type connectors because they ensures a low noise integrity of the supply voltage even if longer cables are used, given high quality coax cables are being used. Additionally SMA power connectors are becoming more and more industry standard on evaluation kits for RF circuit design.

Trying it on for size: The ABPSM-ULN-A is extremely compact

Trying it on for size: The ABPSM-ULN-A is extremely compact

Let’s have a look at the most important part: the noise density. The datasheet presents a maximum noise density of 80nV / √Hz at 100 Hz, 25 nV / √Hz at 1 kHz, and 20 nV / √Hz at 10 kHz. Note that Abracom depicts maximum values in the datasheet. The typical noise density at 1 kHz can be expected to be around 7 nV / √Hz at 1 kHz. For comparison, at 100 Hz, a normal linear voltage regulator has a noise density of about 1 – 1.5 µV / √Hz [2]!

Abracon ABPSM ultra low noise power supply

Abracon ABPSM ultra low noise power supply

The numbers in the datasheet seem to be extremely conservative, though. The following graph shows the actual noise density, which outperforms the values given in the datasheet by far:

Noise density of the ABPSM-ULN-A

Noise density of the ABPSM-ULN-A

The power supply makes a pretty good impression. The only improvement suggestion I really have is a power LED. Better would be 4 LEDs, one for each channel. However, I don’t know whether or not that is practicable as LEDs are excellent noise sources. But a simple power LED for the whole device should be doable in a future revision.

DigiKey has the ABPSM-ULN-A in stock for 393.75 per piece [<a href='http://www.digikey.com/product-detail/en/ABPSM-ULN-A/535-10307-ND/2242563' target='_blank'>3</a>]. Low noise lab power supplies suitable for feeding sensitive Audio and / or RF solutions are usually in the1K range. Additionally, they are usually much heavier and not suitable for portable use. Abracon’s solution is perfect for quick and affordable bench tests.

In case you are curious on just how much power supply noise affects oscillator phase noise in RF design, you should check out the Application Report SLWA066 from Texas Instruments titled “Supply Noise Effect on Oscillator Phase Noise” [4].

UPDATE: Abracon responded to my wish for a power LED:

The reason we had decided not to use LED’s at all was the potential of degrading the noise density. Since we are in the nV / sqrt (Hz) range, everything counts.

We will consider adding a single RED LED in the subsequent iteration on the main power line though.

Links and Sources:

[1] ABPSM-ULN-A Datasheet, Abracon: http://www.abracon.com

[2] Understanding noise in linear regulators, Texas Instruments Incorporated: http://www.ti.com/

[3] ABPSM-ULN-A, DigiKey: http://www.digikey.com/

[4] Supply Noise Effect on Oscillator Phase Noise, Texas Instruments Incorporated: http://www.ti.com/

Please cite this article as:
Westerhold, S. (2012), "Review: Abracon ABPSM-ULN-A - Precision Power Supply Module". Baltic Lab High Frequency Projects Blog. ISSN (Online): 2751-8140., https://baltic-lab.com/2012/09/review-abracon-abpsm-uln-a-precision-power-supply-module/, (accessed: March 28, 2024).

Funding:

If you liked this content, please consider contributing. Any help is greatly appreciated.

2 thoughts on “Review: Abracon ABPSM-ULN-A – Precision Power Supply Module

  1. Hmmm… This thing looks like an expensive thing to solve a simple solution. For the lowest noise supply, why can’t we use a simple battery instead? A battery is completely removed from the likes of mains switching to DC converter that comes with this kit? If a regulator is required after the battery, there are some impressive low 1/F noise linear/LDO regulators out there – but a direct battery connection may be optimal?

Leave a comment

Your email address will not be published. Required fields are marked *